General Specification For Crusher

2. GYRATORY CRUSHERS - 911 Metallurgist

GYRATORY CRUSHERS The original patent for the gyratory crusher was granted to Phile- tus W. Gates in 1881. This fint crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small

Get Price

GUIDE SPECIFICATIONS FOR TENNIS COURT CONSTRUCTION

(f) general information on lighting, fencing, nets, net posts, windscreens, maintenance and resurfacing. 1.1.3 Selection of Tennis Court Contractor. Once working specifications have been developed, a qualified contractor should be selected. Consideration of the following factors is recommended: (a) Submissions should be based on similar

Get Price

Cone Crushers | McLanahan

Cone Crusher Applications. A general rule of thumb for applying Cone Crushers is the reduction ratio. A crusher with coarse style liners would typically have a 6:1 reduction ratio. Thus, with a 3⁄4" closed side setting, the maximum feed would be 6 x 3⁄4 or 4.5 inches. Reduction ratios of 8:1 may be possible in certain coarse crushing applications. Fine liner configurations typically have

Get Price

MOBILE CRUSHING AND SCREENING PLANTS PRODUCT RANGE

Crusher unblocking system (option) Intuitive SPECTIVE control concept Feed capacity up to approx. 220 t/h Crusher inlet (W x D) 950 x 550 mm Weight 30,000 kg* Engine power 155 - 165 kW** MC 100(i) EVO Low consumption diesel direct-drive concept Hydraulic crushing gap adjustment via control system Crusher unblocking system (option)

Get Price

AASHTO M 147 - Standard Specification for

01.01.2017· This specification covers the quality and grading of sand-clay mixtures; gravel, stone, or slag screenings; or sand, crusher run coarse aggregate consisting of gravel, crushed stone, or slag with or without soil mortar or any combination of these materials for use in the construction of subbase, base, and surface courses. The values stated in SI units are to be regarded as the standard

Get Price

5 Aggregate Specifications and Requirements

Specifications and the current Supplemental Specifications. The specifications for aggregates are detailed in Section 904 and other sections for the various types of construction. These specifications are to be followed when inspecting aggregates. There are two general types of requirements for aggregate: quality and gradation.

Get Price

4 Types of Stone Crushers' Maintenance and

27.05.2021· The working principle of impact crusher is that the spinning rotor under the driving of the motor can genetate strong impact force which make blow bars crush stone material into small pieces. Then the crushed material would be thrown by hammers towards,

Get Price

TECHNICAL SPECIFICATIONS QJ241 JAW CRUSHER

QJ241 JAW CRUSHER ENGINEERING IN MOTION QJ241 JAW CRUSHER KEY SPECIFICATIONS DATA Equipment Single toggle C10 jaw crusher Feed opening 1000 mm x 650 mm / 40" x 26" Optimum feed size 520 mm3 / 21 inch3 Engine C7.1 Acert 168 kW / 225 hp Transport dimensions 13.90 m / 45' 7 ⅜" (l) 2.64 m / 8' 7 ⅞" (w) 3.22 m / 10' 6 ⅝" (h)

Get Price

Cone Crusher - 911 Metallurgist

Several studies have indicated that as a general rule of thumb the break even point for using 10 Ft. crushers in place of 7 Ft. crushers is a plant which will have an overall ore treatment capacity of approximately 40,000 TPD or approximately 8,000,000 TPY. Anything less than that figure should indicate the use of conventional 7 Ft. crushers. Obviously a small four stage crushing plant in

Get Price

August 2015 No. 900 SPECIFICATIONS FOR AGGREGATE FOR

specification ranges for consecutive tests. For Class "A" gravel base course, the field tests taken during any crushing shift shall yield an average of 65% or lower passing the 4.75mm sieve.

Get Price